End Caps 0 products
Lozier gondola end units are the components that determine whether your aisle terminations look intentional or incomplete. End caps on a Lozier run are not decorative afterthoughts: they are structural finish pieces that close the exposed Uprite face at the end of every island section run, cover the Base Bracket profile, and present a clean merchandising surface to the shopper walking the aisle end. Getting the depth and finish right before ordering prevents a costly rework when installation begins.
Depth selection for Lozier gondola end caps follows the same logic as the island sections they terminate. A 13-inch depth is standard for health and beauty and HBC runs. Drug and convenience stores typically spec 16-inch depth. Grocery and general merchandise installations run 19-inch or 22-inch depth. Hardware and auto sections require 25-inch depth. The Base End Trim must match the Base Bracket depth exactly: ordering a 16-inch Base End Trim against a 19-inch Base Bracket leaves a 3-inch gap that exposes the bracket heel and fails inspection by most chain planogram teams.
The most common ordering error on Lozier end caps is finish mismatch against an existing store installation. Platinum (PLT), the standard light beige finish, and Charcoal (CHR) are the two stocked finish options. If your existing run was installed in PLT, confirm the PLT designation before ordering: a number of operators have inadvertently ordered Optional Catalog Colors against a PLT field installation because the two can appear similar in low-resolution product photography. Optional Catalog Colors carry an 8 to 10 week lead time and cannot be expedited. The Uprite end trim and Base End Trim must also be ordered as a matched pair; ordering one component in PLT and the other in CHR creates a visible seam mismatch at the aisle cap that cannot be corrected without a full reorder.
Call 800-934-6798 or email dan@rxshelving.com to confirm finish availability, depth compatibility, and lead times before placing your end cap order.
End caps are the highest-revenue-per-square-foot fixture in most retail formats: the display height, depth, and graphic support you specify here determines how much merchandising leverage the vendor or category manager gets per reset.
- Heights: 48, 54, 60, 66, 72, and 78in
- Depths: 13, 16, 19, and 22in
- Base types: LB (Low Base 6in), 06 Standard (8in), TL (T-Leg, no base deck required)
- Vertical Graphic Channel (WEDVGC): full-height side graphic panel for brand or program signage
- End Cap Topper Sign Holder (ECSH): accepts signs up to 20in tall for aisle-entry brand calls
- Maximum height reduces by 12in on carpet or with a glass door kit installed on one side
- Standard finish: Platinum (PLT)
Configuration Reference
Lozier Base End Trim closes the exposed Base Bracket face at the terminus of an island gondola run. It must match the Base Bracket depth exactly: a 19-inch Base End Trim pairs with a 19-inch Base Bracket. Mismatching depth by even one size leaves the bracket heel exposed and fails most planogram compliance reviews.
Lozier end cap Uprite end trim attaches to the face of the outermost Uprite in a run and must be ordered in the same finish as the island section Uprites. Platinum (PLT) and Charcoal (CHR) are standard stocked finishes. Optional Catalog Colors require 8 to 10 weeks and should be confirmed against your project timeline before ordering.
End cap components are finish-matched at the factory and are not interchangeable across finish codes. A PLT Base End Trim and a CHR Uprite end trim cannot be combined on the same end unit without a visible color break at the joint. Order all end cap trim pieces under the same finish code in a single purchase to maintain visual consistency.
Standard Lozier island section widths are 36 and 48 inches. End cap trim components are specified by Uprite height and Base Bracket depth, not by section width. Confirm both the Uprite height and the Base Bracket depth from your existing installation before ordering replacement or addition end cap parts.
Frequently Asked Questions
How do I know which depth to order for my Lozier gondola end caps?
Match the end cap depth to the Base Bracket depth in your existing island section run. If your gondola is built on 19-inch Base Brackets, you need 19-inch Base End Trim. Ordering a shallower trim piece against a deeper bracket leaves the bracket heel exposed and creates a planogram compliance failure at the aisle end.
What is the difference between Base End Trim and Uprite end trim on a Lozier gondola end cap?
Base End Trim closes the face of the Base Bracket at the bottom of the end unit, while Uprite end trim covers the exposed vertical face of the outermost Lozier Uprite. Both components must be ordered in the same finish code and are typically replaced or added as a matched pair to maintain a consistent appearance at the aisle termination.
Lozier gondola end cap finish codes PLT vs CHR
Platinum (PLT) is the standard light beige Lozier finish and is the most common field installation across grocery, drug, and general merchandise stores. Charcoal (CHR) is the standard dark finish. Both are stocked finishes, though availability by specific SKU and depth combination should always be confirmed before ordering on a time-sensitive project.
How long does it take to get Lozier end cap parts in a color other than Platinum or Charcoal?
Lozier end cap components in Optional Catalog Colors, any finish outside of Platinum (PLT) and Charcoal (CHR), carry an 8 to 10 week lead time from the Lozier factory. These lead times cannot be expedited. If your project has a hard installation date, confirm finish availability and order Optional Catalog Color end cap parts well ahead of your schedule.