Wall Sections

WIDESPAN GRAVITY FLOW WIRE FRONT,48W,6H

SKU: WSGFF46.W08

In Stock

$35.33per piece

Total: $35.33

QUANTITY

Request a custom quote

FinishCool White (W08)

Lozier Wall Section, 48"W x 6"H, Cool White finish. Compatible with standard Lozier gondola shelving uprights and base brackets.

Wall sections are a single-face fixture: every linear foot of wall run you configure here is your full perimeter merchandising capacity, and the depth and height combination you select determines both facing density and whether an anchoring requirement applies.

Widths: 2ft (24in), 30in, 3ft (36in), and 4ft (48in)
Heights: 36 to 120in
Depths: 13 to 28in (single merchandising face; no back panel on the wall side)
Base types: 06 Standard Base (8in height) or LB Low Base (6in height)
Bracket types: S (Spring Locking) or HD (Heavy Duty, requires HD uprite)
Anchoring required when height exceeds the stability ratio for the specified depth: 13in=54in, 16in=72in, 19in=90in, 22in=108in, 25in=120in, 28in=144in
Standard finishes: CHR (Charcoal Black) base front, PLT (Platinum) uprite
Back panel options: P, M, ME, W, PW, PM, S, SI, or NBR on the merchandising face

Compatibility: Wall sections connect between two wall gondola uprights and mount against the perimeter wall. Only the outward-facing side carries a back panel and shelves; no back panel is installed on the wall side. Anchoring requirement is determined by the height-to-depth ratio: any configuration where section height exceeds the maximum standalone height for the specified depth requires a wall anchor. Heavy Duty (HD) brackets require an HD uprite. For sections 78in and taller, two-piece back panels are required with a Splicer Rail at the mid-height joint. The run terminates with a Wall End Display (WED) end cap fixture at each open end.

Designed for: Perimeter wall runs in grocery, C-store, drug, specialty retail, and general merchandise formats. Refrigerated case adjacencies, high-bay perimeter aisles, and any layout where the full wall capacity is the merchandising surface and back-of-fixture access is not a planogram consideration.

Configuration Reference

Lozier wall sections in this catalog are available in widths of 24, 30, 36, and 48 inches. Heights range from 48 to 96 inches, covering standard 6-foot and 8-foot perimeter wall heights used in most retail formats. Section depth options run from 13 to 36 inches, giving planners flexibility across product categories that no single island depth can match.

Charcoal (CHR) and W08 are the standard finishes for Lozier wall sections in this category and typically ship within 1 to 2 weeks depending on SKU and depth combination. Platinum (P) and Silver (SIL) are Optional Catalog Colors with an 8 to 10 week production lead time. Never assume finish availability without confirming the specific SKU with your sales contact.

Lozier wall Uprites use a one-inch slotted pattern on a single face, which allows shelf height adjustment in one-inch increments without tools. This differs structurally from island Uprites, which are slotted on two faces. Mixing wall and island Uprites within the same section violates load rating requirements and creates visual alignment problems across the run.

Tilt-In (TL) and Drop-In (DL) shelves are both compatible with Lozier wall section Uprites when the Base Bracket depth matches the shelf depth in the same section. For wall sections 25 inches deep and greater, confirming bracket-to-shelf depth alignment is critical because undersized Base Brackets reduce the rated capacity of the entire section, not just the base level.

Frequently Asked Questions

How do I know which depth to order for my Lozier wall sections?

Match section depth to your product category first. Thirteen-inch depth works for health and beauty, 16-inch fits drug and convenience, 19-inch and 22-inch handle grocery and general merchandise, and 25-inch covers hardware and automotive. This catalog also carries a 36-inch wall section depth for high-cube perimeter storage programs. Your Base Bracket depth must equal the shelf depth you plan to use in the same section.

What is the difference between Charcoal and Cool White finish on Lozier wall sections?

Charcoal (CHR) and Cool White (W08) are both standard finishes that ship within 1 to 2 weeks from Lozier distribution. Silver Vein (SIL) is an Optional Catalog Color requiring 8 to 10 weeks of production lead time in this category. If your installation uses an optional color and you need replacement or expansion sections quickly, call to confirm current lead time before committing to a project schedule.

Lozier wall section Uprite compatibility with island sections

Lozier wall Uprites are slotted on one face only, while island Uprites carry slots on two faces. They share the same one-inch slot spacing but are not interchangeable within a section run. Substituting an island Uprite for a wall Uprite mid-run compromises structural integrity and will misalign Base Brackets, Back Extensions, and Top Rails across the affected sections.

Can I add Lozier wall sections to an existing installation if my store already has gondola shelving in place?

Yes, provided the new wall sections match the Uprite height, finish code, and depth of your existing installation. The critical check is confirming your current Uprite part number before ordering, since Lozier has produced wall Uprites in multiple heights from 48 to 96 inches and the Base Bracket depth must match across all sections in a continuous run. Call 800-934-6798 to verify compatibility before ordering.